Home / Tools & Accessories / Cold Process Tools

Injector Soap Tool

Quantity
         


4.0075.00

Average Review:

 
(11)
See Reviews | Review this Product

Injector Soap Tool (12 cc capacity syringe): As seen on Soap Queen TV- this tool is a necessity for the tiny details in your melt and pour soap projects.

Tips: Trim the tip of the injector using scissors. We like to remove about 1/4” but you can cut more or less depending on your preference. Keep a cup of hot boiling water nearby while using your injector. Clean out the injector in between uses to ensure the soap doesn’t solidify in the tool.

For more tips on using the soap injector see our video on Soap Queen TV ‘Gingerbread Man Soap’

Product Reviews

Average Review:
Review and Rate this Item

Showing 1 - 5 of 11 Reviews:

 

Verified Purchase
Elizabeth
7/30/2017
Fabulous Tool!!!

I have a lot of customers who like MP soap with cute designs. I was losing my mind trying to get the fine details without glopping soap everywhere and making a mess. This tool makes a lot more molds doable for me. You do have to rinse it to keep the soap from hardening inside it, but that's not too difficult. Thank you Brambleberry for another great tool!

Verified Purchase
Rene'
1/11/2017
UNHAPPINESS

I have been using and ordering the injector tools from BB for years and never thought I would be so dismayed that I felt compelled to write a bad review. The tools "used" to be great, but now I can barely get more than two uses out of one tool before having to get out another one! I do a whole lot of injecting in my molds so having to use this many really breaks the bank!

Kelsey from Bramble Berry replies...
Hi Rene! I'm sorry about the clogging. We love the Injector Soap Tool and find it handy for all sorts of design projects, though it can clog up if the soap hardens in the tube. It helps to keep cup of hot soapy water nearby, that way you can clean the tool out before any soap clogs inside. See an example in the Celtic Melt and Pour Soap Tutorial. Customer service has contacted you directly to find out more about the change you mentioned. :-)

Verified Purchase
Jane
11/25/2015
Was excited but now disappointed

I bought this tool to use for the gingerbread man soap. It worked well at first and I had my boiling water beside me. Although, the injector started melting after awhile. I had to cut it , but after that, it was sloppy looking and the soap eventually hardened even with my regular rinsing. I had to use my pipette, but the pipette was more reliable. I recommend using a pipette, because its cheaper and if you mess up, you won't be wasting that much money.

Terah from Bramble Berry replies...
Hi Jane! I'm so sorry that happened to your injector. While we do suggest having a bowl of hot, soapy water near to keep the Injector Soap Tool from clogging, we would not recommend having that water so hot it is boiling. This tool is made from plastic so it can melt at high heats! See an example of this tool being used and cleaned in the Eggcellent Easter Melt & Pour tutorial.


Pam
10/22/2015
Love these

I've been using these for many projects in the past. I did purchase these else where a few years ago. The trick of using these is to take a small amount of oil and apply to the black rubber part when they stick. They will then work just fine and last a long time. In fact I clean and take them apart and set the black part to soak in some oil until I'm ready to use again.


Verified Purchase
Vanessa
9/12/2015
Difficult to use

I bought two of these and couldn't get them to work. I kept my melt-and-pour hot and worked near a boiling pot of water so my soap base wouldn't harden in the syringe. However, i had a hard time pushing the plunger down to get more soap out of the tool.. There was an air pocket and the soap wouldn't go down, no matter how many times I dunked it in the pot of boiling water. :(
123